Crown XTi6002 Power Amplifier with DSP (6000 Watts)

Tune your PA system with the most powerful power amp in Crown's XTi series. The 6002 is packed with DSP for limiting, EQ, crossovers, and subharmonic synth. Requires 20 Amp circuit.

$2,710.00

  • 18 x  
  • 12 x  
    $225.83
  • 8 x  
    $338.75

Crown XTi6000 Power Amplifier (6000 Watts)

No longer available at zZounds
Light and powerful, the Crown XTi6000 power amplifier stands up the demands of a professional PA system while delivering uncolored sound.

The Crown XTI6000 Power Amplifier is a rugged and lightweight power amp that offers unmatched value in its class. Providing up to 6,000 watts into a 4 ohm bridged load and weighing in at just 24 pounds, the XTI6000 sets a new standard in high-power, lightweight amplification.

The XTI6000 also inherits all the best features from the family line, the XTI Series, including powerful integrated speaker processing and an extremely efficient universal tracking switch-mode power supply.

When you're out with the XTI6000, you can count on having the best in music and voice reproduction with more power than ever.

Features
- Integrated proprietary DSP with LCD front panel display
- Accurate, uncolored sound with very low distortion for the best in music and voice reproduction
- Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
- Extremely versatile, handling a wide range of speaker impedances and outputs
- Switch-mode universal power supply
- Speaker presets for crossover frequencies, EQ, limiting, and delay
- All products fill 2U rack spaces and weigh under 17 pounds; weight sets a new standard in lightweight amps (20% less)
- Speakon and binding post outputs, XLR inputs and loop-thrus
- Comprehensive LED status per channel
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications

Output Power (1kHz Power) (With 0.5% THD):
- 2 ohm Stereo (per channel) (With 1% THD): 3,000 Watts
- 4 ohm Stereo (per channel): 2,100 Watts
- 8 ohm Stereo (per channel): 1,200 Watts
- 4 ohm Bridge-Mono (With 1% THD): 6,000 Watts
- 8 ohm Bridge-Mono: 4,200 Watts

- Requires 20A AC Power
- Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V
- Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz): +0/-1 dB
- Signal to Noise Ratio (below rated 1 kHz power at 8 ohms), A-weighted: 100 dB
- Damping Factor (8 ohm): 20 Hz to 400 Hz: > 500
- Input Stage: Input is electronically balanced and employs precision 1% resistors
- At Idle: Draws no more than 90 watts
- Crosstalk (below rated power) 20 Hz to 1 kHz: > 70 dB
- Input Impedance (nominal):
- 20 kilohms balanced
- 10 kilohms unbalanced
- Load impedance (note: safe with all types of loads) Stereo: 2-8 ohms, Bridge mono: 4-16 ohms
- Voltage Gain (at 1 kHz, 8 ohm rated output): 37.1 dB
- Maximum Input Signal: +22 dBu typical
- Operating Temperature: 0* C to 40* C at 95% relative humidity (non-condensing)
- AC Line Voltage and Frequency Configurations Available (+/- 10%): 100V, 120V, 220-240V 50/60 Hz
- Ventilation: Flow-through ventilation from front to back
- Cooling: Heat sinks and proportional-speed fan
- Dimensions (W x H x D) (behind mounting surface): 19 x 3.5 x 16.2 inches (48.26 x 8.9 x 41.15 cm)

Weight:
- Net Weight: 24 pounds (10.9 kg)
- Shipping Weight: 30 pounds (13.6 kg)

For support or warranty questions, please contact the manufacturer:
Phone: 800-342-6939