Shure Beta 27 Condenser Microphone
![Shure Beta 27 Condenser Microphone, New, Front](https://cf1.zzounds.com/media/productmedia/fit,2018by3200/quality,85/4fdb6441a4d896083b8290a4b0ab7f57_813409-99d0e52e40b0fe9a6ae63a632afef078.jpg)
![Shure Beta 27 Condenser Microphone, New, Side](https://cf1.zzounds.com/media/productmedia/fit,2018by3200/quality,85/0575ce789c0ed12ff1d5d9a748dea5ad_813409-317237603a062e6cc830bfd5f5d57aa3.jpg)
![Shure Beta 27 Condenser Microphone, New, Rear](https://cf1.zzounds.com/media/productmedia/fit,2018by3200/quality,85/13dc092b3c288034fb88bc00d994b7c8_813409-692445e4e71714b73362a1b91adcf592.jpg)
![Shure Beta 27 Condenser Microphone, New, Package Contents](https://cf1.zzounds.com/media/productmedia/fit,2018by3200/quality,85/7b9970a0909888453a73a7d3de29a697_813409-7f1d70a53be4f8c7c9a811f30459e96c.jpg)
Acoustically isolate drums, amp cabinets, and instruments with the Beta 27's tight supercardioid pattern. It's ideal for "live in the studio" recordings.
Overview
The Shure Beta 27 is a side-address condenser microphone that is precision engineered for professional sound reinforcement and project studio recording applications. Its flat frequency response and low self noise provide unerring performance in demanding environments. A tight supercardioid pattern insures high gain before feedback, and maximum isolation from other sound sources.
- Tailored for superior transient response from a low-mass, 1 inch externally-biased, ultra-thin 24 Karat gold-layered Mylar diaphragm.
- Flat, neutral frequency response for natural reproduction on stage or in the studio
- 3-position switchable low-frequency filter helps reduce unwanted background noise or counteract proximity effect for consistent, extended low-end
- -15 dB switchable attenuator handles extremely high SPLs with ease
- Premium electronic components and gold-plated internal and external connectors
- Internal pop filter with three separate mesh layers reduces wind and breath noise.
Features:
- Supercardioid polar pattern specifically targets the sound source consistently with greatly minimized bleed from off-axis sound sources- Tailored for superior transient response from a low-mass, 1 inch externally-biased, ultra-thin 24 Karat gold-layered Mylar diaphragm.
- Flat, neutral frequency response for natural reproduction on stage or in the studio
- 3-position switchable low-frequency filter helps reduce unwanted background noise or counteract proximity effect for consistent, extended low-end
- -15 dB switchable attenuator handles extremely high SPLs with ease
- Premium electronic components and gold-plated internal and external connectors
- Internal pop filter with three separate mesh layers reduces wind and breath noise.
Specs
Type: Condenser (externally biased)
Frequency Response: 20 to 20,000 Hz
Polar Pattern: Supercardioid
Impedance: 160 Ohm
Sensitivity (at 1 kHz, open circuit voltage):
- -37 dBV/Pa
- 1 Pascal=94 dB SPL
Maximum SPL (1 kHz at 1% THD):
- 1000 Ohm load: 134 dB (148 dB, Pad on)
- 2500 Ohm load: 140 dB (154 dB, Pad on)
Signal-to-Noise Ratio (referenced at 94 dB SPL at 1 kHz):
- 85.5 dB
- S/N ratio is difference between 94 dB SPL and equivalent SPL of self noise, A-weighted
Dynamic Range (at 1 kHz):
- 1000 Ohm load: 125.5 dB
- 2500 Ohm load: 131.5 dB
Common Mode Rejection (20 Hz to 20 kHz): > 50 dB
Clipping Level (20Hz-20 kHz at 1% THD):
- 1000 Ohm load: 2.0 dBV
- 2500 Ohm load: 8.5 dBV
- THD of microphone preamplifier when applied input signal is equivalent to cartridge output at specified SPL
Self-Noise (typical, equivalent SPL, A-weighted): 8.5 dB
Polarity: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Weight: Net: 428 g (15.1 oz.)
Switch:
- Attenuator: -15 dB
- Low Frequency Response: flat; -6 dB/octave below 115 Hz; -18 dB/octave below 80 Hz
Connector: Three-pin professional audio (XLR), male
Power Requirements: 48v DC phantom, 5.6 mA
Frequency Response: 20 to 20,000 Hz
Polar Pattern: Supercardioid
Impedance: 160 Ohm
Sensitivity (at 1 kHz, open circuit voltage):
- -37 dBV/Pa
- 1 Pascal=94 dB SPL
Maximum SPL (1 kHz at 1% THD):
- 1000 Ohm load: 134 dB (148 dB, Pad on)
- 2500 Ohm load: 140 dB (154 dB, Pad on)
Signal-to-Noise Ratio (referenced at 94 dB SPL at 1 kHz):
- 85.5 dB
- S/N ratio is difference between 94 dB SPL and equivalent SPL of self noise, A-weighted
Dynamic Range (at 1 kHz):
- 1000 Ohm load: 125.5 dB
- 2500 Ohm load: 131.5 dB
Common Mode Rejection (20 Hz to 20 kHz): > 50 dB
Clipping Level (20Hz-20 kHz at 1% THD):
- 1000 Ohm load: 2.0 dBV
- 2500 Ohm load: 8.5 dBV
- THD of microphone preamplifier when applied input signal is equivalent to cartridge output at specified SPL
Self-Noise (typical, equivalent SPL, A-weighted): 8.5 dB
Polarity: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Weight: Net: 428 g (15.1 oz.)
Switch:
- Attenuator: -15 dB
- Low Frequency Response: flat; -6 dB/octave below 115 Hz; -18 dB/octave below 80 Hz
Connector: Three-pin professional audio (XLR), male
Power Requirements: 48v DC phantom, 5.6 mA
- Dimensions and Weight in Packaging
- Base Item
- Shipping Weight: 2.25 lbs
- Shipping Dimensions: 10 x 6 x 4 in
- Manufacturer Part Number (MPN): SHU BETA27
Documents and Manuals
For support or warranty questions, please contact the manufacturer:
Phone: 800-516-2525
Email: service@shure.com
Phone: 800-516-2525
Email: service@shure.com
New
$419.00
- 8 x$52.38
This is a carousel with product cards. Use the previous and next buttons to navigate.
People who bought this item also bought
This is a carousel with product cards. Use the previous and next buttons to navigate.