HeadRush FRFR112 MKII Bluetooth Powered Speaker Cabinet (2500 Watts)

With a huge amount of headroom and a wide, flat frequency response, the stage-friendly FRFR-112 MKII is the perfect platform for pedals and amp modelers.

The Headrush FRFR-112 MKII is a 2500 Watt powered speaker with Bluetooth that is precision-designed to get the most out of your modeler and deliver all the intricacies of your amp and cab emulations, with enough volume to be ready for any stage, rehearsal or jam session.

If you're new to FRFR amplifiers FRFR stands for "full-range flat-response." This special type of amplification is very important for amp modeling pedals and pedalboards, as your amplifier needs to sound pure and transparent, so it can deliver a true "amp in the room" sound without coloring it as a traditional guitar amp would.

PURE AND POWERFUL TONE
FRFR-112 MKII outputs a massive 2500 watts, which means you have enough headroom for almost any performance or rehearsal.
Featuring a specially voiced 12-inch woofer and high-frequency compression driver, the FRFR-112 MKII delivers a precise, full response across the entire frequency range, without any artificial coloration--which is critical to getting the most out of your amp modeler. The FRFR-112 MKII's performance is exceptional, with max 131dB SPL and 46-22kHz frequency range.

ALL THE CONNECTIONS YOU NEED - INCLUDING BLUETOOTH(R)
FRFR-112 MKII features two combo XLR + 1/4" combo inputs for connecting your amp modeling pedal or pedalboard, each with their own independent volume controls. You can also wirelessly connect a mobile device to the FRFR-112 MKII via Bluetooth, so you can stream music wirelessly at rehearsal or during set breaks. There is also an read more XLR output for chaining more than one speaker together or sending the signal from your FRFR out to a front of house mix.

ADAPTS TO ANY STAGE OR ROOM
Stages and rehearsal rooms can easily become dense and muddy sounding as lower frequencies from different instruments battle each other; FRFR-112 MKII has a HPF cut switch to quickly pull those troublesome frequencies out and make sure your tone sits perfect in the mix. Unwanted electrical noise can also be a common problem; FRFR-112 MKII's ground lift switch can eliminate hums and buzzes resulting from ground loops.

ROAD-READY LIGHTWEIGHT DESIGN
FRFR-112 MKII is rugged yet relatively lightweight and easy to transport (at 35lbs / 15.8kg) making one trip load-ins at the gig or rehearsal space easier than ever. While you can use FRFR-112 MKII in its intended wedge position, its versatile design means that it can also be used in an upright or pole-mounted position, making it easier to direct your sound wherever you need it, which is especially helpful at outdoor gigs or other places where PA backline is limited.

Features:

- 2500 Watts
- Bluetooth capability
- Specially voiced 12-inch woofer and high-frequency compression driver
- Two combo XLR + 1/4" combo inputs
- Rugged yet relatively lightweight
WARNING: Cancer and Reproductive Harm - www.p65Warnings.ca.gov.
read less

- Output Power: 2500 W
- Drivers:
- Low-Frequency: 12.0" (305 mm) driver, 2.5" (63 mm) high-temperature voice coil.
- High-Frequency: 1.0" (25 mm) exit ceramic driver with 1.4" (35 mm) coil.
- Crossover Frequency 2 kHz
- Maximum SPL 131 dB (peak) dB-SPL @ 1 m
- Frequency Response 53 Hz - 20 kHz (+/-3 dB)
- Frequency Range 44 Hz - 20 kHz (-10 dB)
- Horn Coverage 90* horizontal x 60* vertical (nominal)
- Connectors:
- (2) XLR+1/4" (6.35 mm) TRS combo inputs (Balanced)
- XLR output (Link)
- IEC power cable input
- Input Impedance Line: 10 KO balanced, 20 KO unbalanced
- Gain/Volume Control Range -8 to 0 dB, +4 dBu nominal, +10 dBu for max output
- HPF Switch 100 Hz
- Bluetooth:
- Version: 5.0
- Profile: A2DP, AVRCP
- Codec: SBC
- Range: up to 100 feet (30.5m)
- Power:
- Connection: IEC
- Input Voltage: 100-120V, 50/60 Hz; 220-240V, 50/60 Hz
- Consumption: 1100W
- Fuse: T15AL AC250V; 220-240V T6.3AL AC250V
- Protection Electronic clip, thermal, and transducer overdrive protection
- Mounting/Installation Standard 36 mm pole socket
- Operating Temperature 14*F to 113*F (-10*C to 45*C)
- Dimensions (width x depth x height): 13.9" x 13.8" x 23.9" (351 mm x 354 mm x 607 mm)
- Weight: 34.7 lbs. (15.7 kg)
Dimensions and Weight in Packaging
Base Item
Shipping Weight: 35.3 lbs
Shipping Dimensions: 26 x 17 x 17 in
Manufacturer Part Number (MPN): FRFR112MK2XUS

For support or warranty questions, please contact the manufacturer:
Phone: 401-658-3131
Web: https://www.headrushfx.com/support

New

$399.00
  • 8 x  
    $49.88
FREE -Day Shipping!
Get it  for
Get it by if you order within
Shipping to