Customer Kudos
"My husband has ordered from zZounds since he was a kid. He swears by this company and refuses to buy elsewhere so this amp is a gift for him he has been wanting."
Search Results
-
Hosa Grounded Power Y-Cable
Power two keyboards, an amp and pedalboard, or your computer and monitor. The 14-inch Hosa Grounded Power Y-cable saves space anywhere you need two outlets.
-
Hosa XLM XLR3 Male Connector
Making or repairing custom cables for line level signals? Replace or terminate your XLR cable with this robust male connector end.
-
Hosa SLW-333 Passive Audio Switcher
Hosa's SLW-333 allows you to listen back on different monitors or switch between three different audio sources without the need to rewire your entire setup!
-
Hosa SKT 12-Gauge Speakon to Speakon Cable
Built to handle the demands of high-current situations, these tough cables are not intended for line-level signals.
$194.95
- No Credit Check6 x$32.49
-
Hosa Double Banana Speaker Cable
Connect power amplifiers to passive speakers with these speaker cables from Hosa, with oxygen-free copper wire and banana plug terminations on both ends.
-
Hosa RMT-254 Table Top Rack
Got a bunch of gear on your desk? Rack it up for easy placement and better organization with the Hosa RMT-254 19-inch table top equipment rack.
-
Hosa RMT-152 19-inch, 12-Space Rolling Rack
Clean up your act! The Hosa RMT-152 19-inch, 12-space rolling equipment rack keeps your live or studio equipment organized and within arm's reach.
$128.95
- No Credit Check6 x$21.49
-
Hosa RCA-025 RCA Connector
Terminate your custom cables wit this pair of Hosa RCA connectors. Color-coded red and white bands make it easy to mark left and right channels.
-
Hosa PWP-461 IEC C7 Polar NEMA 1-15P Power Cable
Need a replacement power cord for gear with a polarized C8 inlet? Hosa's PWP-461 cable has a figure-8 C7 plug and an 8-foot cable to get you powered up.
-
Hosa 3-Wire Grounded Right Angle Power Cable
If space is tight in the back of your rack or keyboard rig, save space with this right-angled IEC power cord. It works with any gear that has a C14 inlet.
-
Hosa PLG-025W 1/4 Inch TS Wide Opening Connector
Wire up your own speaker cables! This Hosa 1/4" TS connector is a perfect fit for wider gauge cables used for unbalanced mono signals.
-
Hosa PLG-025S 1/4" TRS Connector
Cap your homemade cables with this Hosa PLG-025S TRS connector. It works for balanced mono and unbalanced stereo uses and is ideal for line-level signals.
-
Hosa PHX-106M Low-voltage Adaptor PHX3M to XLR3 Male Connector
Connect your XLR pro audio equipment to consumer equipment using Phoenix connectors with the Hosa PHX-106M low-voltage PHX3M to male XLR3 connector.
-
Hosa PHX-106F Low-voltage Adaptor XLR3 Female to PHX3M Connector
Need to connect bare wire to something with an XLR out? This specialized Hosa adapter makes it possible, with a PHX3M connector on one end.
-
Hosa PDC-373 Daisy Chain Extension Cord
Direct ideal current to four separate pedals! Hosa's PDC-373 daisy chain extension cord makes directing DC power easy with four 2.1 mm DC pedal power jacks.
-
Hosa MST-224 Desktop Microphone Stand
Hosa's MST-224 mini microphone stand supports your mic on a desk or table, then folds flat to fit in your bag -- great for mobile recording setups.
-
Hosa MPA-149 XLRM to XLRF Active Preamplifier
Boost the signal of your low-output dynamic or ribbon microphones with this in-line preamp that keeps your setup minimal and offers up to +26dB of gain!
$97.95- No Credit Check4 x$24.49
-
Hosa MIT-435 XLR Female Lo-Z to 1/4" TS Hi-Z Transformer
Match impedances with this Lo-Z to Hi-Z transformer adapter. This connector steps up a microphone's signal, so you can plug into a high-impedance 1/4" input.
-
Hosa MIT-156 Impedance Matcher Transformer, XLR-3F to 1/8" TRS
You can plug an XLR microphone into a 1/8" stereo audio input when you add this impedance-matching adapter. It's ideal for connecting XLR mics to camcorders.
-
Hosa MIT-129 Female TS 1/4" to XLR Male Impedance Transformer
No Hi-Z instrument jack? Use this impedance-matching transformer to plug a high-impedance 1/4" guitar or bass cord into your mixer's low-impedance XLR input.