- Frequency response: 59 Hz to 20 kHz
- Low frequency limit (-3 dB point): 59 Hz
- Usable low frequency limit (-10 dB point): 52 Hz

Internal power amplifiers (@120 VAC line):
- Woofer: 1000 watts peak available power
- Woofer's Continuous Power: 500 watts @ less than 1% distortion
- Tweeter - 500 watts peak available power
- Tweeter's Continuous Power: 250 watts @ less than 1% distortion.

- Nominal sensitivity (1W @1M, swept sine input in anechoic environment): 99 dB (average)
- Maximum sound pressure level: 130 dB music peak
- Nominal radiation angles: 110 degrees horizontal by 30 degrees vertical
- Transducer complement: 12" Neodymium Dual Voice Coil Scorpion woofer, Model SDC1288, and an RD2.6 with 4.75" long aluminum composite ribbon tweeter
- Box tuning frequency (Fbox): 60 Hz
- Electroacoustic crossover frequency: 2,000 Hz
- Crossover Slopes: 24 dB/octave (fourth order) low pass, 24dB/octave (fourth order) high pass, and driver EQ.

Input Connections:
- Two combo female XLR/ 1/4" phone jack providing balanced or unbalanced operation
- 3.5 mm stereo media jack.

Output Connections:
- Two XLR Outputs
- Full Range Thru, electrically buffered with selectable option of Channel A input only, or Ch. A and Ch. B mixed.
- XLR output

- Controls: Ch. 1 and Ch. 1 Gain control knob. Ch. 1 and Ch. 2 Mic/Line gain select pushbutton

- Status Indicators: Blue Illuminated ribbon lens indicates power On, illumination can be turned Off by user. Front baffle red LED indicates DDT activation. Rear panel LCD screen in Input Level mode, shows DDT activation by flashing "DDT" on the LCD screen, right hand side. Signal level indicated by bar graph coming from left hand side of LCD.

- Electronic Crossover: DSP based, with LCD display and Rotary Encoder Knob for selection of EQ presets and Graphic EQ. Crossover Frequency Set to 2.0 kHz. Low Pass slope: 24 dB/octave, High Pass slope: 24 dB/octave

DSP Section Specifications:
- Latency: Approx. 2.7 msec
- ADC and DAC Sampling frequency: 96 kHz
- Bit Depth: 24 bits for ADC/DAC, 32 bits for DSP calculations.

- Enclosure materials and finish: Injection-molded plastic with internal ribbing and bracing, and with textured finish. Molded material is black, as is the metal grille. Grille has cloth backing for elegant looks.

- Mounting: Subwoofer pole-mounting or speaker stand via built-in 1.375" diameter pole mount, flying via VM70 (two groups of four M6 inserts top and bottom), and rubber feet for floor or stage use.

- Dimensions (H x W x D): 24.38" X 14.07" X 14.25" (61.9 cm x 35.7 x 36.2 cm)
- Weight: 39 lbs. (17.7 kg)
- Balanced inputs: 10 k ohms line level sensitivity selected.
- Unbalanced input: 5 k ohms, line level sensitivity selected.
- Mic switch sensitivity Increase: 26 dB
- Input Sensitivity for Full Output (Level full CW): 0.42 V RMS
- Input Overload Point (switch in Line position): +14 dBV
- Infrasonic filter protection: 36 dB/octave roll-off
- Nominal amplifier frequency response: +0, -1 dB from 10 Hz to 30 kHz
- Hum and noise: Greater than 90 dB below rated power
- DDT dynamic range: Greater than 14 dB
- THD and IM: Typically less than 0.1 %
- Damping factor: Greater than 50 @ 1000 Hz, 4 ohms
- Power requirements of Peavey RBN112 system (domestic): Nominal 200 watts, 120 VAC, 60 Hz

- Pole Socket Size: 1-3/8" (35 mm)

Fuse Type:
- For 120 VAC USE: International fuse classification T10AH 250V. In the USA, types GDC, GMC, 215, 218, and 477 cartridge-style 5 x 20 mm size time-delay fuses with a 10 amp 250V rating can be used.
- For 220-240VAC USE: International fuse classification T5AHL 250V. This is a cartridge-style 5 x 20 mm size time-delay fuse with a 5 amp 250V rating.