Marshall DSL100H Amp Head + MX412 Speaker Cab = All-Tube Bliss
The Marshall DSL100H half stack pairs the Marshall DSL100H amplifier head with Marshall's MX412 speaker cabinet. A revamped version of the legendary Marshall DSL100, the DSL100H head preserves the incredible tonal properties of that classic amp, while adding a few modern features that maximize its versatility for contemporary musicians. Add the optional footswitch to take advantage of the DSL100H's true footswitchable 2-channel design.
Learn more with this video from Marshall:
A Classic Valve Design, Reproduced to Spec
Just like the classic DSL100, the DSL100H is an all-valve design boasting 4 x ECC83 and 4 x EL34 tubes. These impart a rich tone from the moment you turn the amp on, and then gradually reveal a complex and rich evolving world of crunch as you push the gain stage.
Resonance Control, 3-Band EQ and Mid-Shift
For more than three decades of hard rock and metal music, the sound of a distorted DSL100 has been a benchmark for musicians crafting powerful tones. Now you can take your own quest for tone even further with the newly-added Resonance control that gives you more control over the low-end weight and balance. There is a 3-band Treble/Middle/Bass EQ as well, which delivers a highly musical range of color for you to explore. A Mid-Shift button allows you to immediately conjure the furious sounds needed for hard rock leads and shredding metal tones.
Add the Optional Footswitch
An optional footswitch allows you to switch between the 2 channels and engage or disengage the DSL100H's on-board digital reverb. The footswitch also allows you to toggle between the Classic Gain and Ultra channels with "Clean/Crunch" and "Lead 1/Lead 2," so you can move effortlessly between the DSL100H's powerful clean tone and the high-gain sizzle you want.
Great I/O Design for Maximum Versatility
The rear panel on the DSL100H features some very thoughtful I/O design. The series FX Loop is fully bypassable via an on/off switch. There is also a Pentode (Full Power)/Triode (Half Power) switch that drops the power amp's output to 50 watts in situations where you still want a crunchy tone, but a less crushing volume. Musicians have been using the DSL100 as a studio amplifier for years, and this feature makes it somewhat more manageable in such situation. There are 2 x 8 ohm outputs to run to cabinets or loudspeakers, and 1 x 16 ohm jack as well.
Half Stack Includes Marshall MX412 Speaker Cabinet
Featuring four Celestion G12E-60 speakers and iconic black covering with white piping, this cab is ready to rock any stage. Pair up the DSL100 with either an angled or straight cab -- both equally classic half-stack combinations.
Check out our exclusive run-down of the Marshall DSL100H Guitar Amplifier:
Marshall DSL100H Amp Head Features:
- Footswitchable 2-channel design
- FX loop with true-bypass switch
- Treble/Middle/Bass EQ controls
- Presence and Resonance controls
- Digital reverb
- Mid-Shift button
- 4 x ECC83 and 4 x EL34 all-tube design
- Pentode/Triode switch
- 2 x 8 ohm and 1 x 16 ohm outputs
Marshall MX412 Speaker Cabinet Features:
- Four Celestion G12E-60 12 inch Speakers
- Black Covering and White Piping
- Marshall Logo
- MDF Construction
zZounds is an authorized dealer of Marshall products.
- Pre-amp valves: 3 x ECC83
- Power-amp valves: 1 x ECC83, 4 x EL34
- Dual footswitch channels
- 2 modes per channel
- 3 band EQ, Mid-shift, and Presence
- Resonance control
- Digital Reverb
- Pentode/Triode switch
- Series FX Loop (Bypassable)
- Footswitch included
- Dimensions WxHxD mm - (741x274x242)
- Weight: 24.2 kg
- Weight, Dimensions, and Manufacturer Part Numbers
- with MX412A (Angled)
- with MX412B (Straight)