Event 2030 Powered Studio Monitor Speaker (3-Way)
No longer available at zZounds
Hear the critical midrange accurately with Event's three-way powered studio monitors, with a redesigned waveguide to optimize dispersion and power response.
Overview
The Event 2030 is a category defining three-way studio monitoring system. It combines three discrete drivers to allow for incredibly accurate reproduction of the entire audio spectrum.
Rather than simply adding a mid-range driver to the 20/20BAS configuration which could have been easily achieved, Event's engineers took the three-way concept to a higher level, resulting in a class-defining speaker system with compelling audio performance and a physical embodiment that makes it ideal for use in near field applications. A wave guide assembly was designed to house the speaker's mid-range and high frequency drivers as well as optimize audio dispersion and power response characteristics.
For the critical mid-range application a 3.5-inch cone transducer was engineered using a pressed pulp and polypropylene cone, combined with an optimized magnetic circuit. The driver is loaded onto a shallow wave guide that results in increased sensitivity and output while generating very low distortion artifacts, giving the 2030 speaker system an incredibly defined, upfront vocal character.
Combined with an aluminum alloy dome tweeter, the mid-high wave guide assembly employs an optimized set of electronic acoustic filters, derived from Event's flagship Opal studio monitor, to maximize phase, time correction and frequency response characteristics. The resulting signal processing achieves controlled audio reproduction and smooth frequency response performance extending well above 20 kHz.
A key… read more design feature of the 2030 amplifier is use of a proprietary, soft clipping power amplifier design topology that never allows the amplifier's output waveform to become jagged or harsh. This results in a speaker system whose character stays consistent no matter what the output level, as audible distortion artifacts kept under control.
The Event 2030 combines precisely engineered acoustic design, signal processing and amplifier technology to provide an incredibly detailed and wide soundstage with a bass response that far exceeds what most would expect from a box this size.
- Crossover points at 400 Hz and 3 kHz
- 7.1" dedicated woofer
- 3.5" dedicated midrange driver for outstanding vocal reproduction
- 0.75" dome tweeter
- Rear-firing port
- Frequency range of 38 Hz to 22 kHz read less
Rather than simply adding a mid-range driver to the 20/20BAS configuration which could have been easily achieved, Event's engineers took the three-way concept to a higher level, resulting in a class-defining speaker system with compelling audio performance and a physical embodiment that makes it ideal for use in near field applications. A wave guide assembly was designed to house the speaker's mid-range and high frequency drivers as well as optimize audio dispersion and power response characteristics.
For the critical mid-range application a 3.5-inch cone transducer was engineered using a pressed pulp and polypropylene cone, combined with an optimized magnetic circuit. The driver is loaded onto a shallow wave guide that results in increased sensitivity and output while generating very low distortion artifacts, giving the 2030 speaker system an incredibly defined, upfront vocal character.
Combined with an aluminum alloy dome tweeter, the mid-high wave guide assembly employs an optimized set of electronic acoustic filters, derived from Event's flagship Opal studio monitor, to maximize phase, time correction and frequency response characteristics. The resulting signal processing achieves controlled audio reproduction and smooth frequency response performance extending well above 20 kHz.
A key… read more design feature of the 2030 amplifier is use of a proprietary, soft clipping power amplifier design topology that never allows the amplifier's output waveform to become jagged or harsh. This results in a speaker system whose character stays consistent no matter what the output level, as audible distortion artifacts kept under control.
The Event 2030 combines precisely engineered acoustic design, signal processing and amplifier technology to provide an incredibly detailed and wide soundstage with a bass response that far exceeds what most would expect from a box this size.
Features:
- Three-way powered nearfield monitor speaker- Crossover points at 400 Hz and 3 kHz
- 7.1" dedicated woofer
- 3.5" dedicated midrange driver for outstanding vocal reproduction
- 0.75" dome tweeter
- Rear-firing port
- Frequency range of 38 Hz to 22 kHz read less
Specs
- Type: Three-way, bass reflex
- Frequency Response: 38Hz - 22kHz
- Crossover Frequencies: 400Hz & 3kHz
- Crossover Type: Linkwitz-Riley Acoustic fourth order for Low/Mid range; Event Proprietary Acoustic second order for Mid/High range.
- Low Frequency Filter: Butterworth Subsonic Second Order (-3dB at 38Hz)
- Acoustic Output - SPL at 1m, Long term (80Hz - 20kHz): 111dB
- Acoustic Output - SPL at 1m, Peak (80Hz - 20kHz): 114dB
- Signal Input: XLR (balanced)
- AC Input Connector: 3-Pin IEC
- Average Long Term Power Consumption: 95 watts
- Quiescent Power Consumption: <10 watts
- Overdrive Protection: Event proprietary IC based fast limiting with sliding gain
- Thermal Protection: Thermal cutoff switch, auto reset
- Low frequency transducer:
- Piston Diameter: 180mm (7.1")
- Voice Coil Diameter: 38mm (1.5")
- Former Material: Kapton
- Voice Coil Wire: Copper
- Magnet Type: Ferrite (fully shielded)
- Cone Type: Mineral Filled Polypropylene
- Mid Range Transducer:
- Piston Diameter: 85mm (3.3")
- Voice Coil Diameter: 25mm (1")
- Former Material: Glass fiber
- Voice Coil Wire: Copper
- Magnet Type: Ferrite
- Cone Type: Pressed pulp/Mineral filled polypropylene
- High Frequency Transducer:
- Piston Diameter: 19mm (0.75")
- Voice Coil Diameter: 19mm (0.75")
- Magnet Type: Neodymium (fully shielded)
- Cone Type: Aluminum alloy with Ferrofluid cooled magnetic gap
- Low Frequency Amplifier:
- Frequency Response: 20Hz - 40kHz (+/- 0.25dB) bandwidth limited
- Operating Band Pass: 20Hz - 400Hz
- Total Harmonic Distortion: 0.02% at 120 watts into 4ohm load
- Long Term Power at 4 Ohms: 80 watts
- Power at 4 Ohms: 120 watts
- Output Topology: Class AB with proprietary soft clipping topology
- Cooling: Convection - Aluminium heat sink
- High Frequency Amplifier:
- Frequency Response: 20Hz - 40kHz (+/- 0.25dB) (bandwidth limited)
- Operating Band Pass: 400Hz - 30kHz
- Total Harmonic Distortion: 0.02% at 120 watts into 4ohm load
- Long Term Power at 6 Ohms: 80 watts
- Power at 6 Ohms: 120 watts
- Output Topology: Class AB with proprietary soft clipping technology
- Cooling: Convection - Aluminium heat sink
- Physical:
- Cabinet Construction: Engineered Composite Wood
- Low Frequency Vent: High "Q" / High output rear fi ring port
- Cabinet Volume: 16 Litres
- Cabinet Dimensions (W x H x D): 275 x 300 x 260 mm, (10.8 x 11.8 x 10.2 in.)
- Cabinet Weight: 14.6kg/32lb
- Operating Temperature Range: 5-35 deg C / 40-95 deg F
- Power Supply:
- Type: Torodial
- Rating: 270VA
- AC mains fuse and AC voltage selector: 100V-120V 5 Amp, 220V-250V 2.5 Amp
- Frequency Response: 38Hz - 22kHz
- Crossover Frequencies: 400Hz & 3kHz
- Crossover Type: Linkwitz-Riley Acoustic fourth order for Low/Mid range; Event Proprietary Acoustic second order for Mid/High range.
- Low Frequency Filter: Butterworth Subsonic Second Order (-3dB at 38Hz)
- Acoustic Output - SPL at 1m, Long term (80Hz - 20kHz): 111dB
- Acoustic Output - SPL at 1m, Peak (80Hz - 20kHz): 114dB
- Signal Input: XLR (balanced)
- AC Input Connector: 3-Pin IEC
- Average Long Term Power Consumption: 95 watts
- Quiescent Power Consumption: <10 watts
- Overdrive Protection: Event proprietary IC based fast limiting with sliding gain
- Thermal Protection: Thermal cutoff switch, auto reset
- Low frequency transducer:
- Piston Diameter: 180mm (7.1")
- Voice Coil Diameter: 38mm (1.5")
- Former Material: Kapton
- Voice Coil Wire: Copper
- Magnet Type: Ferrite (fully shielded)
- Cone Type: Mineral Filled Polypropylene
- Mid Range Transducer:
- Piston Diameter: 85mm (3.3")
- Voice Coil Diameter: 25mm (1")
- Former Material: Glass fiber
- Voice Coil Wire: Copper
- Magnet Type: Ferrite
- Cone Type: Pressed pulp/Mineral filled polypropylene
- High Frequency Transducer:
- Piston Diameter: 19mm (0.75")
- Voice Coil Diameter: 19mm (0.75")
- Magnet Type: Neodymium (fully shielded)
- Cone Type: Aluminum alloy with Ferrofluid cooled magnetic gap
- Low Frequency Amplifier:
- Frequency Response: 20Hz - 40kHz (+/- 0.25dB) bandwidth limited
- Operating Band Pass: 20Hz - 400Hz
- Total Harmonic Distortion: 0.02% at 120 watts into 4ohm load
- Long Term Power at 4 Ohms: 80 watts
- Power at 4 Ohms: 120 watts
- Output Topology: Class AB with proprietary soft clipping topology
- Cooling: Convection - Aluminium heat sink
- High Frequency Amplifier:
- Frequency Response: 20Hz - 40kHz (+/- 0.25dB) (bandwidth limited)
- Operating Band Pass: 400Hz - 30kHz
- Total Harmonic Distortion: 0.02% at 120 watts into 4ohm load
- Long Term Power at 6 Ohms: 80 watts
- Power at 6 Ohms: 120 watts
- Output Topology: Class AB with proprietary soft clipping technology
- Cooling: Convection - Aluminium heat sink
- Physical:
- Cabinet Construction: Engineered Composite Wood
- Low Frequency Vent: High "Q" / High output rear fi ring port
- Cabinet Volume: 16 Litres
- Cabinet Dimensions (W x H x D): 275 x 300 x 260 mm, (10.8 x 11.8 x 10.2 in.)
- Cabinet Weight: 14.6kg/32lb
- Operating Temperature Range: 5-35 deg C / 40-95 deg F
- Power Supply:
- Type: Torodial
- Rating: 270VA
- AC mains fuse and AC voltage selector: 100V-120V 5 Amp, 220V-250V 2.5 Amp
No longer available at zZounds
In most cases, a product is unavailable because it has been discontinued by the manufacturer
This is a carousel with product cards. Use the previous and next buttons to navigate.
People who bought this item also bought
Universal Audio Apollo Twin X Duo Thunderbolt 3 Audio Interface
$999.00
- 12 x$83.25
- 8 x$124.88
- No Credit Check6 x$166.50
- No Credit Check4 x$249.75
Yamaha HS8S Active Studio Subwoofer
$499.99
- 8 x$62.50
- No Credit Check6 x$83.33
- No Credit Check4 x$125.00
Shure SM7B Dynamic Cardioid Studio Vocal Microphone
$399.00
- 8 x$49.88
- No Credit Check6 x$66.50
- No Credit Check4 x$99.75
Focusrite Scarlett 2i2 Gen 4 USB Audio Interface
$199.99
- No Credit Check6 x$33.33
- No Credit Check4 x$50.00
Neumann TLM 102 Studio Microphone
$749.00
- 12 x$62.42
- 8 x$93.63
- No Credit Check6 x$124.83
- No Credit Check4 x$187.25
JBL LSR310S Powered Studio Subwoofer Speaker
$349.00
- 8 x$43.63
- No Credit Check6 x$58.17
- No Credit Check4 x$87.25
Universal Audio Apollo Solo Thunderbolt 3 Audio Interface
$499.00
- 8 x$62.38
- No Credit Check6 x$83.17
- No Credit Check4 x$124.75
Neumann TLM 103 Studio Microphone
$1,195.00
- 18 x
- 12 x$99.58
- 8 x$149.38
- No Credit Check6 x$199.17
- No Credit Check4 x$298.75
KRK S10.4 Powered Studio Subwoofer (160 Watts)
$479.00
- 8 x$59.88
- No Credit Check6 x$79.83
- No Credit Check4 x$119.75