Samson S83 Mixer Amplifier

No longer available at zZounds
This is a carousel with one large image and a track of thumbnails on the left side. Select any of the thumbnail buttons to change the main image. You may also use the left and right arrow keys to navigate between images.
open zoom image for Samson S83 Mixer Amplifier, Main
Samson S83 Mixer Amplifier, Main
zZounds Gear Experts Say...
19 in. rackmount mixer amplifier. 300 watts at 4 ohms.

Fully loaded in terms of features and performance, the S83 is another standout in Samson's popular line of powered mixers. Equipped with high-quality reverb, the unit includes enough Sends and Returns so you always have adequate mixing capability. A stereo 1/4 in. headphone connector with separate level control allows isolated monitoring.

Features
8-channel powered mixer with balanced XLR mic/line inputs

Power amp produces 300 watts into 4 ohms

Rugged reinforced corners and a carry handle plus rack ears for rack-mounting

3-spring reverb section

2 Aux sends per channel

4 effects returns for outboard processing

Mic input control on each channel

Master monitor and reverb level controls

Headphone amp with 1/4 in. stereo TRS connector and level control for private monitoring

Front-panel output level meter

4-band EQ on each channel

10-band master graphic EQ on main output

Selectable 48v phantom power

Protection relay circuitry

Rear-panel amplifier input and preamp output

Mixer/Preamp Section
THD (with 30 kHz LPF, trim center): < 0.045%

Signal-to-noise ratio (with 30 kHz LPF, trim center): 78 dB

Maximum voltage gain

Mic in to preamp out: effects send 1, 2, mon out: 62 dB

Line in to preamp out: effects send 1, 2, mon out: 52 dB

Tape in to preamp out: effects send 10 dB

Tape return to preamp out: 5 dB

Residual noise (with 30 kHz LPF, VR min)

Preamp out: -110 dB

Mon out: -100 dB

Trim gain: 40 dB

Tone controls
High (10 kHz): ± 15 dB
2.5 kHz: ± 12 dB
500 Hz ± 12 dB
Low (80 Hz): ± 15 dB
Graphic equalizer (30, 64, 125, 250, 500 Hz, 1, 2, 3, 5, 10 kHz): ± 15 dB
Peak LED: 5 dB before clipping
Tape input sensitivity (-10 dB): 300 mV
Headphone: 20 mW (8 .)

Power Amp Section
Rated output power (1 kHz): 300 W into 4 .
220 W into 8 .
THD (with 30 kHz LPF): < 0.0045%
Signal-to-noise ratio (with 30 kHz LPF): 105 dB
Frequency response (±1 dB): 10 Hz to 28 kHz
Input sensitivity/impedance: 1.2 V/10 k
Residual noise (VR min): 74 dB typical
Idle current (across the 0.47 .emitter resistor): < 7 mA
DC offset voltage: 0 ± 50 mV


General
Dimensions (W x D x H): 451 x 125 x 280mm (19 x 4.92 x 11.02 in.)
Weight: 31 lbs. (14.1 kg)
Power requirements: 115 VAC x 50/60 Hz; 544 W (115 VAC)
Power consumption (at full power): 395 W (230/240 VAC)

For support or warranty questions, please contact the manufacturer:
Phone: 516-870-7200
Web: http://www.samsontech.com/contact/

Be the first to rate and review this product.

No longer available at zZounds

In most cases, a product is unavailable because it has been discontinued by the manufacturer